For Sale / Used Equipment the Waste Paper Industry / Balers / #704 Print »
IBS 44:9.
Presona Baler LP-50-VH/2 - 2005.
Filling Opening: 1´500mm x 1´100mm.
Capacity = 340 cubic meters pro hour.
Capacity tons pro hour.
Material 30 kg pro cubic meter = 8 - 10 tons.
Material 50 kg pro cubic meter = 11 - 13 tons.
Material 100 kg pro cubic meter = 15 - 22 tons
Bale size: 1´100 x 720 mm x adj.length.
Bale weights: 400 - 550 Kg/m³.
Wires: 5 Vertical.
Press Force: 50 tons.
Specific pressure: 6,4 Kp / cm²
Max Oilpressure: 250 Bar.
Oil tank Volume: 600 l.
Electric Motor: 37 KW.
Weight Baler: 18 tons.

All above technical specifications are taken from Presona leaflets.

.

View from the front.
Picture inside the Baler.
The thickness from the Bottomplate at the openings where the Needles operate up and down and the wear is at most is as most is between 10,0 and 12 mm.
Picture inside the Baler.
The thickness from the Bottomplate at the openings where the Needles operate up and down and the wear is at most is as most is between 10,0 and 12 mm.
The Baler is equipped with Presona´s Option Material Distibutor.

The Material Distributor helps making better Bales from News and Books Materials.
View over the front part of the Baler.
The Baler is equipped with 2 Cylinders in the top of the friction channel and 1 setting scew at each side.

One Directional Valve operate those 2 Cylinders.

The Baler is equipped with an program, original from Presona, to be able to change between 5 different " Working Programs " for the Baler.
Using one presssuretransmitter in the hydraulic system, allow us from the Operation Panel to set pressures in the 5 different " Working Programs " for the Baler.
The Baler is equipped with Oil Heater.
The Baler is equipped with Air Oilcooler.
The Operation Panel.
This Baler is equipped with an program, original from Presona, to be able to change between 5 different " Working Programs " for the Baler.
Using one presssuretransmitter in the hydraulic system, allow us from the Operation Panel to set pressures in the 5 different " Working Programs " for the Baler.
Paper shall Always be pressed by as high pressure as possible, plastic shall be pressed with a lower pressure, not to destroy the wires.
Beside above, this Baler is equipped with a propotional hydraulic system, to make all the movements smooteher.
The Baler is also original equipped from Presona with a Very Good Fault Seeking System.
If the Baler stops working, You can read the reason for this stop in the Text Display in the Operation Manual.
View from the side.
We can see the Electric Cabinet.
View indside the Electric Cabinet.
Picture from the back of the Balers.
You can see the mounting from the Motor with the Hydraulic Pump.
The inlet from the oil to the Pump is below the Oil Level - Propotional Hydraulic System.
Picture over the Tying Unit - BN2P - 5 bent needles from the bottom.

A Really Good Tying System,, maybe the best ever made for Paper Balers.
Picture over the left Prepress Bearing.
The Bearing is a Little worned and I send with a New Bearing when I sell this Baler.
Picture over the right Prepress Bearing.
The Bearing is a Little worned and I send with a New Bearing when I sell this Baler.
The Baler is Proffesional repaired at the back holder for the Mainpresser Cylinder.
Side Wire Guides.
Back Wire Guides.
Bales made with this Baler.
Bales made with this Baler.

Loading Dimensions and Weights.

Baler.
Length: 8´900 mm.
Width: 2´200 mm.
Height: 2´350mm.
Weight: 16´000 Kg.

Middle Hooper.
Length: 3´010 mm.
Width: 1´550 mm.
Height: 600 mm.
Weight: 800 Kg.

Upper Hooper.
Length: 1´200 mm.
Width: 1´700 mm.
Height: 1´430mm.
Weight: 1´000 Kg.

Upper Part Prepresser.
Length: 1´400 mm.
Width: 1´100 mm.
Height: 500 mm.
Weight: 300 Kg.

Wirepuller.
Length: 2´900 mm.
Width: 1´200 mm.
Height: 1´250 mm.
Weight: 600 Kg.

Electric Cabinet.
Length: 2´000mm.
Width: 1´400mm.
Height: 350mm.
Weight: 300 Kg.

Operation Panel.
Length: 970mm.
Width: 500mm.
Height: 500mm.
Weight: 80 Kg.